Cadence® system design and verification solutions, integrated under our System Development Suite, provide the simulation, acceleration, emulation, and management capabilities.
System Development Suite Related Products A-Z
Cadence® digital design and signoff solutions provide a fast path to design closure and better predictability, helping you meet your power, performance, and area (PPA) targets.
Full-Flow Digital Solution Related Products A-Z
Cadence® custom, analog, and RF design solutions can help you save time by automating many routine tasks, from block-level and mixed-signal simulation to routing and library characterization.
Overview Related Products A-Z
Driving efficiency and accuracy in advanced packaging, system planning, and multi-fabric interoperability, Cadence® package implementation products deliver the automation and accuracy.
Cadence® PCB design solutions enable shorter, more predictable design cycles with greater integration of component design and system-level simulation for a constraint-driven flow.
An open IP platform for you to customize your app-driven SoC design.
Comprehensive solutions and methodologies.
Helping you meet your broader business goals.
A global customer support infrastructure with around-the-clock help.
24/7 Support - Cadence Online Support
Locate the latest software updates, service request, technical documentation, solutions and more in your personalized environment.
Cadence offers various software services for download. This page describes our offerings, including the Allegro FREE Physical Viewer.
Get the most out of your investment in Cadence technologies through a wide range of training offerings.
This course combines our Allegro PCB Editor Basic Techniques, followed by Allegro PCB Editor Intermediate Techniques.
Virtuoso Analog Design Environment Verifier 16.7
Learn learn to perform requirements-driven analog verification using the Virtuoso ADE Verifier tool.
Exchange ideas, news, technical information, and best practices.
The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information.
It's not all about the technlogy. Here we exchange ideas on the Cadence Academic Network and other subjects of general interest.
Cadence is a leading provider of system design tools, software, IP, and services.
trying to simulate a chopper amplifier. For testing it is configured as a voltage follower. There is only one clock all the non overlapping clocks ect are derived from it. The problem is that the flicker noise is not being reduced on the input noise plot when I use the following pnoise, pss settings:
pss pss fund=100k harms=3 errpreset=conservative+ annotate=statuspnoise ( out 0 ) pnoise sweeptype=relative relharmnum=1+ start=1 stop=50k log=20 maxsideband=20 iprobe=V2 refsideband=0+ annotate=status
I have tried various settings and cannot reduce the flicker noise. I have verified that the chopper is working and it does remove the dc offset when inserting a non zero vdc at the inputs in the time simulation. I have also tried following the chopper opamp with a with a sample and hold and taking the output for pnoise simulation from the sample and hold but this still does not reduce the flicker noise seen on the direct plot.
I've read Ken Kundert's sc-filters.pdf from www.designers-guide.org/Analysis/ and have successfully used pss and pnoise to simulate an oscillator in the past following the spectreRF tutorial.
There has been a few posts on this site as well as others but the only advise given is to eternally point people to Ken Kundert's sc-filters.pdf or the cadence manual.
Any ideas where I'm going wrong with the simulation setup?
In reply to BenMartin:
BenMartinI have the same question. I don't see 1/f noise being modulated away from the origin. Did you ever figure it out?
It should be set to the zero harmonic ie relharmnum=0 not relharmnum=1 as that starts the sweep around the clock (see my original spectre settings above) which was not the intention. After that the settings are fine and the chopper works as desired regarding 1/f noise.
The error was obvious but no thanks to this forum though.
In reply to harmonics:
Sorry, been rather busy over the last few weeks and did not have a chance to read this through carefully and spot the error. Unfortunately the symptoms weren't that clear, but you're right - it's an obvious mistake, since the input and output frequency of the amplifier are the same.