~~~~~~~~~~~~~~~~~~~~~~
Pre-Simulation Summary
~~~~~~~~~~~~~~~~~~~~~~
~~~~~~~~~~~~~~~~~~~~~~
Entering remote command mode using MPSC service (spectre, ipi, v0.0, spectre0_30173_7, ).

Warning from spectre.
	WARNING (SPECTRE-16707): Only tran supports psfxl format, result of other analyses will be in psfbin format.


******************
DC Analysis `dcOp'
******************

Notice from spectre during DC analysis `dcOp'.
	No checklimit analysis defined for asserts. A default checklimit analysis 'SpectreChecklimitAnal' has been created with all asserts enabled.

The following asserts will be enabled for all subsequent analyses until the next checklimit analysis statement is found:
temperature_min_check : ON
temperature_max_check : ON
N21.egnfet_gate_source_terminal_check : ON
N21.egnfet_drain_source_terminal_check : ON
N21.egnfet_body_source_terminal_check : ON
N21.egnfet_drain_body_terminal_check : ON
N21.egnfet_gate_drain_terminal_check : ON
N21.egnfet_gate_body_terminal_check : ON
N20.egnfet_gate_source_terminal_check : ON
N20.egnfet_drain_source_terminal_check : ON
N20.egnfet_body_source_terminal_check : ON
N20.egnfet_drain_body_terminal_check : ON
N20.egnfet_gate_drain_terminal_check : ON
N20.egnfet_gate_body_terminal_check : ON
N0.egnfet_gate_source_terminal_check : ON
N0.egnfet_drain_source_terminal_check : ON
N0.egnfet_body_source_terminal_check : ON
N0.egnfet_drain_body_terminal_check : ON
N0.egnfet_gate_drain_terminal_check : ON
N0.egnfet_gate_body_terminal_check : ON
N19.egnfet_gate_source_terminal_check : ON
N19.egnfet_drain_source_terminal_check : ON
N19.egnfet_body_source_terminal_check : ON
N19.egnfet_drain_body_terminal_check : ON
N19.egnfet_gate_drain_terminal_check : ON
N19.egnfet_gate_body_terminal_check : ON

Opening the PSF file ../psf/dcOp.dc ...
Important parameter values:
	reltol = 1e-03
	abstol(V) = 1 uV
	abstol(I) = 1 pA
	temp = 27 C
	tnom = 27 C
	tempeffects = all
	gmindc = 1 pS
Trying `homotopy = gmin'.

Maximum value achieved for any signal of each quantity:
V: V(net01) = 4.149 V
I: I(V6:p) = 50 uA
Convergence achieved in 216 iterations.
DC simulation time: CPU = 634.902 ms, elapsed = 1.70052 s.
Total time required for dc analysis `dcOp': CPU = 32.994 ms, elapsed = 65.5391 ms.
Time accumulated: CPU = 634.902 ms, elapsed = 1.70167 s.
Peak resident memory used = 86.3 Mbytes.

dcOpInfo: writing operating point information to rawfile.

Opening the PSF file ../psf/dcOpInfo.info ...
modelParameter: writing model parameter values to rawfile.

Opening the PSF file ../psf/modelParameter.info ...
element: writing instance parameter values to rawfile.

Opening the PSF file ../psf/element.info ...
outputParameter: writing output parameter values to rawfile.

Opening the PSF file ../psf/outputParameter.info ...
designParamVals: writing netlist parameters to rawfile.

Opening the PSFASCII file ../psf/designParamVals.info ...
primitives: writing primitives to rawfile.

Opening the PSFASCII file ../psf/primitives.info.primitives ...
subckts: writing subcircuits to rawfile.

Opening the PSFASCII file ../psf/subckts.info.subckts ...