Adams

CDNS Forum Adams Categories

Adams Car

Adams Community

Adams Car On Demand

Adams Beta

Adams Modeler Beta

Forum - Thread List

Latest Posts

Not Answered

Is it possible to change the global coordinate system in ADAMS after the model is built? like rotate/translate the entire model?

Category: Adams

By BAntkowi
•
updated over 6 years ago by BAntkowi

3 replies • 6 views
Not Answered

Change result sets marker from global to another one

Category: Adams

By amine.tiar
•
updated over 6 years ago by Jesper Slattengren

3 replies • 0 views
Not Answered

Getting 'Compliance matrix calculation failed' error on SPMM testrig. Can someone please help me resolve this?

Category: Adams Car

By 1ndeshmu
•
updated over 6 years ago by 1ndeshmu

1 replies • 5 views
Not Answered

Can you export model in step file (run model) after running mechanism at end step ?? I want model file at the end of step of mechanism.

Category: Adams

By abhishek.kulkarni
•
updated over 6 years ago by Maziar R

1 replies • 2 views
Not Answered

Reduction Gear Input Joint assign with a Joint communicator

Category: Adams

By burford.john
•
updated over 6 years ago by Jesper Slattengren

1 replies • 2 views
Not Answered

Kingping Angle at zero wheel travel is different in suspension parallel wheel travel and SPMM.

Category: Adams

By dmvachhani
•
updated over 6 years ago by dmvachhani

3 replies • 1 views
Not Answered

Is it possible to deactivate contact forces for step1 of 1sec and then activate that contact forces on next step 2 of time?? .

Category: Adams

By abhishek.kulkarni
•
updated over 6 years ago by Jesper Slattengren

2 replies • 1 views
Not Answered

Flex warning: Edge with no mate found. The shell may not be water tight.

Category: Adams

By erik_spe
•
updated over 6 years ago by Jesper Slattengren

3 replies • 9 views
Not Answered

For ADAMS-EDEM co-simulation, is it possible to analyse the results obtained from EDEM?

Category: Adams

By k.pang
•
updated over 6 years ago by Jesper Slattengren

1 replies • 3 views
Answered

Hi! Is it possible to implement, using Adams View Controls Toolkit, a controls block which multiplies input signals?

Category: Adams

By pawel.kozlowski
•
updated over 6 years ago by pawel.kozlowski

5 replies • 14 views
Not Answered

What would cause an error with "straight line" steering input but not free/locked?

Category: Adams Car

By Jonathan Corno
•
updated over 6 years ago by Jesper Slattengren

3 replies • 14 views
Not Answered

How to apply torque with time and angle dependent? I need to apply incremental torque on shaft with angle of rotation and also need to constraint with time. Currently using motion and torque to achieve but is there any way that can avoid using motion.?

Category: Adams

By abhishek.kulkarni
•
updated over 6 years ago by abhishek.kulkarni

4 replies • 2 views
Not Answered

Example of ADAMS REQUEST citing "Variables" Documentation is ambiguous regarding exactly what constitutes "variable"

Category: Adams

By stephen.s.gates
•
updated over 6 years ago by Kent West

2 replies • 2 views
Not Answered

Is it possible to hide the contact forces generated in animation ?? . I want to see the mechanism as per load condition . Is there any hide option??

Category: Adams

By abhishek.kulkarni
•
updated over 6 years ago by abhishek.kulkarni

2 replies • 1 views
Not Answered

Is there any option to add friction (Static & dynamic ) to the screw joint.? Appreciate your suggestions.

Category: Adams

By binu.jose
•
updated over 6 years ago by Jesper Slattengren

1 replies • 0 views

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.