Physical System Simulation

CDNS Forum Physical Categories

Actran

Adams

CAEFatigue

Cradle CFD

Digimat

Dytran

Easy 5

Elements

FTI FormingSuite

Marc

MaterialCenter

MSC Apex

MSC Apex Generative Design

MSC CoSim

MSC Nastran

ODYSSEE

Patran

Romax

SimManager

Simufact

Virtual Test Drive

Physical System Simulation

Latest Posts

Not Answered

Is there a way to vary the mnf file for a flex body within cases generated by Insight? It doesn't seem to take a design variable within View.

Category: Adams

By sarah.m.callan
•
updated over 5 years ago by michael.w.clarke

4 replies • 9 views
Not Answered

Hello, can someone tell me how is the engine map defined in EVIA databse (EVIA is a acar database from adm 745 Adams Car Electric Vehicle Modeling)? Thank you for any help!

Category: Adams

By mate.basic
•
updated over 5 years ago by mate.basic

3 replies • 9 views
Answered

How to refine the mesh on hotspot locations?

Category: MSC Apex

By elijah.d.lamppin.civ
•
updated over 5 years ago by Darrel Sinclair

4 replies • 43 views
Not Answered

Adams graphics file does not show animation or any kind of geometries when imported into Adams Post Processor. It shows force and other graphics except geometry. Is it issue with ADAMS license or any other issue.

Category: Adams

By s.kakade
•
updated over 5 years ago by Thomas Nygårds

1 replies • 8 views
Not Answered

How to partition this 3D object for 2.5D Hex meshing?

Category: MSC Apex

By elijah.d.lamppin.civ
•
updated over 5 years ago by elijah.d.lamppin.civ

2 replies • 24 views
Not Answered

Using Marc Mentat and model sections. I keep getting inside out elements when starting my analysis. What would cause this? I ran a small model to try to recreate the error and it worked. Does Marc have a problem renumbering larger models? Thanks.

Category: Marc

By Jim
•
updated over 5 years ago by Zach Fata

1 replies • 11 views
Not Answered

Hello I would like to change a solid to a flexible part. I have created a test model with a "cylinder" (R5mm, L200mm) and an "ellipsoid" (D20mm). The cylinder is attached to ground with a revolute joint and to the ellipsoid with a fixe

Category: Adams

By stefan.frei
•
updated over 5 years ago by Maziar R

6 replies • 1 views
Not Answered

Ideas for smoothing solid-flex contacts (PSHELL)?

Category: Adams

By erik_spe
•
updated over 5 years ago by erik_spe

10 replies • 23 views
Not Answered

I am using a simulation script that reduces the error tolerance within the stationary part of the simulation (Solver Hastiff SI1). The saved .msg-file tells me that Gstiff I3 is used. How can I check if the simulation script is performed correctly?

Category: Adams

By philipp.viandt
•
updated over 5 years ago by philipp.viandt

2 replies • 7 views
Not Answered

Why is significantly different maximum reachable velocity in ADAMS CAR 3D road for geometrically identical roads but once used in xml format and once used in crg+crgf format

Category: Adams

By M Mueller
•
updated over 5 years ago by MK202610123211

4 replies • 6 views

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.