Physical System Simulation

CDNS Forum Physical Categories

Actran

Adams

CAEFatigue

Cradle CFD

Digimat

Dytran

Easy 5

Elements

FTI FormingSuite

Marc

MaterialCenter

MSC Apex

MSC Apex Generative Design

MSC CoSim

MSC Nastran

ODYSSEE

Patran

Romax

SimManager

Simufact

Virtual Test Drive

Physical System Simulation

Latest Posts

Answered

Integrated Finite Element Model in Adams

Category: Adams

By Hamed Hani
•
updated over 3 years ago by Jesper Slattengren

4 replies • 12 views
Not Answered

STREAMの質問をさせていただきます。 STREAMで津波と堤防のシミュレーションを行いたいのですが，ソルバーで解析後ポストを起動させた際に添付画像のとおり，節点数が異なるというようなエラーが発生してしまいました。原因と対処法について教えて頂けないでしょうか。よろしくお願いします。

Category: Cradle CFD

By T．Kubota
•
updated over 3 years ago by T．Kubota

2 replies • 6 views
Not Answered

攪拌試験を再現したいのですが、平面ファンの場合はうまくいくのですが、旋回流を考慮するために軸流ファンで回転数を指定して実行すると何も起きません。助けください。また、ほかに攪拌試験を再現するのによい方法があれば教えてください。

Category: Cradle CFD

By hosoya.s.ae
•
updated over 3 years ago by Chuel-Ho.Kim

3 replies • 4 views
Not Answered

When I generate trajectory by selecting nodes at every point, my simulation is not working. But when define the trajectory between two nodes, it works. I dont know why this happens ?

Category: Simufact

By sivasakthi.pachiyappan
•
updated over 3 years ago by anja.grebe

11 replies • 38 views
Not Answered

In the results, at a particular increment between 28 and 30, I observe the sudden displacement of my sheet. I have done many similar simulations, but I never observed this effect. What is the reason ?

Category: Simufact

By sivasakthi.pachiyappan
•
updated over 3 years ago by sivasakthi.pachiyappan

3 replies • 20 views
Not Answered

Rubber modelling in Nastran 101 & 112

Category: MSC Nastran

By manish.musale
•
updated over 3 years ago by Sanjay Patel

1 replies • 10 views
Not Answered

What is the cause of the difference between Adams Insight result based on an Adams Car full-vehicle model and Adams Car manual simulation result? (Only Four-Poster Results)

Category: Adams Car

By canpolatb20
•
updated over 3 years ago by Jesper Slattengren

1 replies • 10 views
Not Answered

can I define absoption coeffficient for the material in laser welding simulation. If yes, where can I find the option

Category: Simufact

By sivasakthi.pachiyappan
•
updated over 3 years ago by C B

3 replies • 9 views
Not Answered

sol200; Is it possible to design modal damping (TABDMP1)?

Category: MSC Nastran

By adam.narozniak
•
updated over 3 years ago by Vivek Bhardwaj

1 replies • 8 views
Not Answered

Force outputs (plotting)

Category: MSC Nastran

By Josef K.
•
updated over 3 years ago by karlR

6 replies • 16 views

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.