• Skip to main content
  • Skip to search
  • Skip to footer
Cadence Home
  • This search text may be transcribed, used, stored, or accessed by our third-party service providers per our Cookie Policy and Privacy Policy.

  1. Community Forums
  2. Physical System Simulation

Following Cadence Design Systems’ acquisition of the Design & Engineering (D&E) business, the D&E Community Forum on the Nexus Community Center has been migrated in the Cadence Physical System Simulation Community. For more details and if you have any questions, please refer to the FAQ.

Physical System Simulation

CDNS Forum Physical Categories

Actran

Adams

CAEFatigue

Cradle CFD

Digimat

Dytran

Easy 5

Elements

FTI FormingSuite

Marc

MaterialCenter

MSC Apex

MSC Apex Generative Design

MSC CoSim

MSC Nastran

ODYSSEE

Patran

Romax

SimManager

Simufact

Virtual Test Drive

Physical System Simulation

Latest Posts

  • Not Answered

    i would like to understand that how we can apply as cohasive + riveting bond between two shell faces. should i have to simply use the tool called cohasive under the element ?.

    Category: MSC Nastran

    By parth.pravinbhai

    •

    updated over 3 years ago by Kiranraj Shetty

    1 replies • 7 views
  • Not Answered

    Speed up contact convergence

    Category: MSC Nastran

    By david.l.agnew5.ctr

    •

    updated over 3 years ago by Kiranraj Shetty

    1 replies • 13 views
  • Not Answered

    Actuator subsystem attachment in General Actuation Analysis

    Category: Adams

    By carlos.ruiz

    •

    updated over 3 years ago by Brian Edwards

    1 replies • 10 views
  • Not Answered

    WARNING: Edge with no mate found - Anybody else had this warning?

    Category: Adams

    By jpatterson

    •

    updated over 3 years ago by Brian Edwards

    1 replies • 10 views
  • Not Answered

    How can I use Adams/Insight (Ascii) to optimize damper values?

    Category: Adams Car

    By canpolatb20

    •

    updated over 3 years ago by canpolatb20

    2 replies • 16 views
  • Not Answered

    寒中コンクリートの採暖養生をシミュレーションしています。養生囲いのシート表面の空気の流速の大きさの平均を、内側外側それぞれ知りたいと思っています。現在、パネルで作成したシートの表面に直方体で属性を条件領域として作成し、出力条件でXYZ方向流速成分を出力していますが、最大最小は分かりますが大きさの平均を出せません。良い方法があればご教授頂ければと思います。ソフトはSTREAMです。イメージを添付いたします。

    Category: Cradle CFD

    By k-furukawa

    •

    updated over 3 years ago by k-furukawa

    4 replies • 16 views
  • Not Answered

    Problem about boundary conditions

    Category: Marc

    By quocnhat.tb

    •

    updated over 3 years ago by dbarlam

    1 replies • 13 views
  • Not Answered

    New 4K Monitors - Graphics settings?

    Category: Adams

    By jpatterson

    •

    updated over 3 years ago by tobias.meisolle

    4 replies • 13 views
  • Not Answered

    Hello, can someone explain me please which temperature "Static" or "Total" is introduced in Flow Boundary - Inflow Temperature conditions for a compressible flow simulation in ScFlow?

    Category: Cradle CFD

    By M Mueller

    •

    updated over 3 years ago by M Mueller

    2 replies • 9 views
  • Not Answered

    Stiff spring element works inside adm but stops converging when defined inside dll

    Category: Adams

    By jbaqersad

    •

    updated over 3 years ago by Micha

    1 replies • 10 views
<>

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.

© 2026 Cadence Design Systems, Inc. All Rights Reserved.

  • Terms of Use
  • Privacy
  • Cookie Policy
  • US Trademarks
  • Do Not Sell or Share My Personal Information