• Skip to main content
  • Skip to search
  • Skip to footer
Cadence Home
  • This search text may be transcribed, used, stored, or accessed by our third-party service providers per our Cookie Policy and Privacy Policy.

  1. Community Forums
  2. Allegro X PCB Editor
  3. Why is a crosstalk table needed for a basic fast autoro...

Stats

  • Replies 6
  • Subscribers 160
  • Views 12294
  • Members are here 0
More Content

Why is a crosstalk table needed for a basic fast autoroute

tmd63
tmd63 over 4 years ago

When attempting to use the autoroute feature in Allegro PCB Editor (design.brd not design.dsn file). The router refuses to run unless a cross-talk simulation is run first.

I just want a simple x-y autoroute done using specific layers where layer 8 is the x direction and layer 10 is the Y direction (for example). I have over 4,000 connections to complete in 4 hours and it is too much for my mouse/fingers/brain to do manually. But the simulation is taking forever to run and will provide no useful help as there are no impedance requirements on the PCB!

So how can I run a simple Autoroute to remove the majority of the simple connections (I have already fanned out most of the connections manually)? Or does Allegro not allow for autorouting any more?

  • Sign in to reply
  • Cancel
Parents
  • redwire
    redwire over 4 years ago

    Hmmm....something is setup wrong.  If you pass the autorouter a constraint and you have the correct license it will follow the rules.   Not sure why you are seeing the crosstalk analysis come up first.  You might try switching your Allegro license down to the base license and try again.

    Otherwise export the autorouter "DSN" file and start the autorouter from the command line and then read in the DSN file.  Hopefully you know the standard setup commands that you need to do before kicking it off?  You will need to set the rules and then start the route.

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • Cancel
  • tmd63
    tmd63 over 4 years ago in reply to redwire

    Thank you, but I do not have a dsn file. I am using Allegro 17.4 and it has a .brd file instead. I am not using OrCAD.

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • Cancel
  • redwire
    redwire over 4 years ago in reply to tmd63

    The BRD gets converted to DSN for the autorouter.  You can do it manually (File->Export...etc) or when you invoke the autorouter it generates the Specctra format DSN file from your BRD.

    Sounds like you might need to tune up your autorouter knowledge before pushing go?

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • Cancel
Reply
  • redwire
    redwire over 4 years ago in reply to tmd63

    The BRD gets converted to DSN for the autorouter.  You can do it manually (File->Export...etc) or when you invoke the autorouter it generates the Specctra format DSN file from your BRD.

    Sounds like you might need to tune up your autorouter knowledge before pushing go?

    • Cancel
    • Vote Up 0 Vote Down
    • Sign in to reply
    • Cancel
Children
No Data
Cadence Guidelines

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.

© 2025 Cadence Design Systems, Inc. All Rights Reserved.

  • Terms of Use
  • Privacy
  • Cookie Policy
  • US Trademarks
  • Do Not Sell or Share My Personal Information