Stats

More Content

PCB Outline

ivy372

Hi guys,

I have write a skill that change origin to low-left of the PCB  board.

But how can I change the origin to the Board outline center point?

-----------------------------------------------------------------------------

axlCmdRegister( "o_ll" 'o_ll ?cmdType "interactive")
(procedure o_ll()
axlExtentDB()
x = -( caar( axlExtentDB()))
y = -( cadar( axlExtentDB()))
axlDBChangeDesignOrigin( x:y )
axlUIConfirm( "Change Origin to LowLeft.")
)

------------------------------------------------------------------------------

Thanks~

Parents
  • 0

    Try something like this:

    outlineShp = car(axlDBGetShapes("BOARD GEOMETRY/DESIGN_OUTLINE")) || car(axlDBGetShapes("BOARD GEOMETRY/OUTLINE"))
    if(outlineShp then
    centrePt = axlMidPointLine(outlineShp ->bBox)
    else
    axlClearSelSet()
    axlSetFindFilter(?enabled '("noall", "invisible", "lines"), ?onButtons '("noall", "lines"))
    axlAddSelectAll()
    outlines = setof(obj, axlGetSelSet(), obj ->layer == "BOARD GEOMETRY/OUTLINE")
    xMin = min(caar(car(outlines) ->bBox), caadr(car(outlines) ->bBox))
    yMin = min(cadar(car(outlines) ->bBox), cadadr(car(outlines) ->bBox))
    xMax = max(caar(car(outlines) ->bBox), caadr(car(outlines) ->bBox))
    yMax = max(cadar(car(outlines) ->bBox), cadadr(car(outlines) ->bBox))
    foreach(line, cdr(outlines)
    xMin = min(caar(line ->bBox), caadr(line ->bBox), xMin)
    yMin = min(cadar(line ->bBox), cadadr(line ->bBox), yMin)
    xMax = max(caar(line ->bBox), caadr(line ->bBox), xMax)
    yMax = max(cadar(line ->bBox), cadadr(line ->bBox), yMax)
    )
    centrePt = axlMidPointLine(list(list(xMin, yMin), list(xMax, yMax)))
    )
    axlDBChangeDesignOrigin(axlMXYSub(0:0, centrePt))

  • 0 in reply to eDave

    Hi eDave,

    Thanks very much~

    But I want to change the origin to the low-left of PCB Board.

    I hope the origin set on the middle line of BOARD GEOMETRY/OUTLINE.

    like below:

  • 0 in reply to ivy372

    axlClearSelSet()
    axlSetFindFilter(?enabled '("noall", "invisible", "linesegs"), ?onButtons '("noall", "linesegs"))
    axlAddSelectAll()
    outlineSegments = setof(obj, axlGetSelSet(), obj ->layer == "BOARD GEOMETRY/OUTLINE")
    axlClearSelSet()
    minx = min(apply('min, mapcar('caar, outlineSegments ~>startEnd)), apply('min, mapcar('caadr, outlineSegments ~>startEnd)))
    miny = min(apply('min, mapcar('cadar, outlineSegments ~>startEnd)), apply('min, mapcar('cadadr, outlineSegments ~>startEnd)))
    axlDBChangeDesignOrigin(axlMXYSub(0:0, minx:miny))

  • 0 in reply to eDave

    Hi eDave,

    Can you please explain me how to execute this code.

    Regards,
    Jithindev

Reply Children
Cadence Guidelines

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.