Stats

  • Locked Locked
  • Replies 4
  • Subscribers 125
  • Views 17919
  • Members are here 0
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Configure Cadence IC after installation

Tony777

Hi everyone,

I have installed Cadence IC 6.15 in a new linux server. This is the first time I did these things. After installation, I don't know how to run it. Because the old server was broken so I cannot refer to it. I know this question is stupid. But, believe me, I have tried for a week. Please help me. Thank so so much.

Parents

  • The original problem would be solved by ensuring you have the libXp rpm installed (make sure you have both the 32-bit and 64-bit versions installed).

    For the libManager start up issue, try running "libManager" from UNIX to make sure it can run and doesn't have any shared libraries missing.

    Then I guess it's probably something wrong with your /etc/hosts setup. A solution ( ) on Cadence Online Support suggests:

    In general, make sure that: /etc/hosts has an entry for localHost and also an entry for itself with a fully qualified domain name and its correct IP address. Add an entry to /etc/hosts for the local hostname and IP-address.

    By default there is only the loop-back address (127.0.0.1) contained in this file. Providing the local hostname as an alias for the loopback address also solves the problem.

    ----------- sample /etc/hosts file ------------------------

    # Do not remove the following line, or various programs
    # that require network functionality will fail.

    127.0.0.1 localhost.localdomain localhost

    172.23.40.73 lx-test lx-test.cadence.com

    However in general I don't think you need a separate entry - I just have this:

    127.0.0.1         lnx-mymachine lnx-mymachine.cadence.com localhost loghost

    where lnx-mymachine is the name of my machine (I have both a short and fully-qualified name there too).

    Regards,

    Andrew.

Reply

  • The original problem would be solved by ensuring you have the libXp rpm installed (make sure you have both the 32-bit and 64-bit versions installed).

    For the libManager start up issue, try running "libManager" from UNIX to make sure it can run and doesn't have any shared libraries missing.

    Then I guess it's probably something wrong with your /etc/hosts setup. A solution ( ) on Cadence Online Support suggests:

    In general, make sure that: /etc/hosts has an entry for localHost and also an entry for itself with a fully qualified domain name and its correct IP address. Add an entry to /etc/hosts for the local hostname and IP-address.

    By default there is only the loop-back address (127.0.0.1) contained in this file. Providing the local hostname as an alias for the loopback address also solves the problem.

    ----------- sample /etc/hosts file ------------------------

    # Do not remove the following line, or various programs
    # that require network functionality will fail.

    127.0.0.1 localhost.localdomain localhost

    172.23.40.73 lx-test lx-test.cadence.com

    However in general I don't think you need a separate entry - I just have this:

    127.0.0.1         lnx-mymachine lnx-mymachine.cadence.com localhost loghost

    where lnx-mymachine is the name of my machine (I have both a short and fully-qualified name there too).

    Regards,

    Andrew.

Children
No Data

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.