Stats

  • Locked Locked
  • Replies 5
  • Subscribers 125
  • Views 2619
  • Members are here 0
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Why spectre generated-netlist always show the wrong subckt name "unmos4_schematic" but not "unmos4" ?

Paulux

Hello,

I want to build a cell called unmos4 and hope the spectre-generated netlist showing as follows

.subckt unmos4 D G S B

parameters nw=1 nl=1

M1(D G S B) ne2 w=nw l=nl as=0.49*(nw) ad=0.49*(nw) pd=0.98+2*(nw) ps=0.98+2*(nw)

ends unmos4

MN0 (out net043 gnd gnd) unmos4 nw=3 nl=0.35

HOWEVER, the result shows that there is extra "_schematic" after unmos4

.subckt unmos4_schematic D G S B

parameters nw=1 nl=1

M1(D G S B) ne2 w=nw l=nl as=0.49*(nw) ad=0.49*(nw) pd=0.98+2*(nw) ps=0.98+2*(nw)

ends unmos4_schematic

MN0 (out net043 gnd gnd) unmos4_schematic nw=3 nl=0.35

 

May I know how to remove "_schematic" after unmos4?

 

The CDF is as follows

Component Parameters

model paramType=string, parseANumber=no, parseAsCEL=yes, storeDefault=no, name=model, prompt=unmos4

Simulation Information

Choose Simulator=spectre, otherParameters=model, instParameters= nw nl, componentName=unmos4, termOrder=d g s b

Same problem of extra "_schematic"  is also found when hspiceD netlisting for simulation.

 Choose Simulator=hspiceD, instParameters= nw nl, componentName=unmos4, namePrefix=X, termOrder=D G S B, termMapping= nil D \,D G\, G S \,S B \,B 

Thank you very much in advance for any help, feedback and comments

Parents
  • Andrew Beckett

     The macroArguments stuff is primarily for stopping views - it's if you want to reference an external subckt model - and it's for hspice - not spectre. Even then I think it's for hspiceS, not hspiceD.

    I believe that the _viewName will only get added if you have used a config and more than one view has been selected - In general it should just use the cellName as the subckt name.

    I'm not sure why it necessarily matters, if everything is consistent - but maybe the best thing is to provide your data (to customer support if you can't provide it here) so that somebody can take a look?

    Regards,

    Andrew.

Reply
  • Andrew Beckett

     The macroArguments stuff is primarily for stopping views - it's if you want to reference an external subckt model - and it's for hspice - not spectre. Even then I think it's for hspiceS, not hspiceD.

    I believe that the _viewName will only get added if you have used a config and more than one view has been selected - In general it should just use the cellName as the subckt name.

    I'm not sure why it necessarily matters, if everything is consistent - but maybe the best thing is to provide your data (to customer support if you can't provide it here) so that somebody can take a look?

    Regards,

    Andrew.

Children
No Data

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.