• Skip to main content
  • Skip to search
  • Skip to footer
Cadence Home
  • This search text may be transcribed, used, stored, or accessed by our third-party service providers per our Cookie Policy and Privacy Policy.

  1. Community Forums
  2. Custom IC Design
  3. cds_ff_mpt PDK?

Stats

  • Locked Locked
  • Replies 7
  • Subscribers 126
  • Views 18182
  • Members are here 0
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

cds_ff_mpt PDK?

rsashwinkumar
rsashwinkumar over 6 years ago

I was trying to install and use BAG2 from github (https://github.com/ucb-art/BAG2_cds_ff_mpt/)

The given instruction asks to download the PDK  "cds_ff_mpt " (cadence generic PDK for finfet and multi-patterned technology) from cadence support site. I was unable to find it in the cadence support. Can someone let me know where to download this from?

  • Cancel
Parents
  • Danielrayray
    Danielrayray over 5 years ago

    Hi, rsashwinkumar and Andrew

    I would like to ask if you confront with the problem that there are no "qrc_options.yaml" file while extracting RC via BAG.

    As I use GUI  to extract, there are no problems. Therefore, I went to see bag_config.yaml to check what is going on. I found that there aren't existing "qrc_options.yaml" 

    I use the same pdk(cds_ff_mpt) as you. 

    If you have any instructions, please let me know.

    here is my email address: rayyeh942@gmail.com

    Appreciate

    Sincerely

    Daniel

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
  • Andrew Beckett
    Andrew Beckett over 5 years ago in reply to Danielrayray

    I know nothing about this "BAG" (I had to do a Google search to figure out that this is the "Berkeley Analog Generator"). The missing file is not a file that is needed by our tools, so I assume it must be something to do with this BAG system. You should contact the maintainer of the repository (or use the Issues page on the GitHub project).

    Andrew.

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
  • Danielrayray
    Danielrayray over 5 years ago in reply to Andrew Beckett

    Dear Andrew,

    Thanks for your rapidly reply. 

    As for this file, I have already consulted with the maintainer of BAG, and he left a message as showed in the following picture.

    He said since Cadence doesn't provide the extraction flow of the cds_ff_mpt; therefore, it is hard to set up "qrc_options.yaml", which is the artifact file written in python to let the BAG system run RC extraction automatically.

    Could I ask about which PDK has provided the supported extraction flow?  Or which file is the "extraction flow" of the cds_ff_mpt downloaded from http://pdk.cadence.com.

    Thanks a lot

    Sincerely

    Daniel

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
  • Andrew Beckett
    Andrew Beckett over 5 years ago in reply to Danielrayray

    Hi Daniel,

    I suspect the maintainer of BAG is talking about an old version of cds_ff_mpt. The 0.3 version didn't have Quantus QRC rules, but the 0.5 version (which is the currently available version on http://pdk.cadence.com )  does  have Quantus QRC rules set up:

    UNIX> /bin/ls -R cds_ff_mpt_v_0.5/qrc
    cds_ff_mpt_v_0.5/qrc:
    best corner.defs typical worst

    cds_ff_mpt_v_0.5/qrc/best:
    RCXdspfINIT _p2lvsfile cds_ff_mpt_best.ict extview.trp lvsfile
    RCXspiceINIT callProc.il compilation_cmd layer_setup qrcTechFile

    cds_ff_mpt_v_0.5/qrc/typical:
    RCXdspfINIT _p2lvsfile cds_ff_mpt_typical.ict extview.trp lvsfile
    RCXspiceINIT callProc.il compilation_cmd layer_setup qrcTechFile

    cds_ff_mpt_v_0.5/qrc/worst:
    RCXdspfINIT _p2lvsfile cds_ff_mpt_worst.ict extview.trp lvsfile
    RCXspiceINIT callProc.il compilation_cmd layer_setup qrcTechFile

    Regards,

    Andrew.

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
  • Danielrayray
    Danielrayray over 5 years ago in reply to Andrew Beckett

    Dear Andrew,

    I got you. I will provide this information to the maintainer and discuss it with him.

    Thanks a lot. You save me lots of time!!

    Sincerely

    Daniel

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
Reply
  • Danielrayray
    Danielrayray over 5 years ago in reply to Andrew Beckett

    Dear Andrew,

    I got you. I will provide this information to the maintainer and discuss it with him.

    Thanks a lot. You save me lots of time!!

    Sincerely

    Daniel

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
Children
No Data

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.

© 2025 Cadence Design Systems, Inc. All Rights Reserved.

  • Terms of Use
  • Privacy
  • Cookie Policy
  • US Trademarks
  • Do Not Sell or Share My Personal Information