Unable to Import .v files with `define using "Cadence Verilog In" tool

Hello,

I am trying to import multiple verilog modules defined in a single file with "`define" directive in the top using Verilog In. The code below is an example of what my file contains.

When I use the settings below to import the modules into a library, it imports it correctly but completely ignores all `define directive; hence when I simulate using any of the modules below the simulator errors out requesting these variables.

My question: Is there a way to make Verilog In consider `define directives in every module cell created? 

Code to be imported by Cadence Verilog In:

--------------------------------------------------------

`timescale 1ns/1ps
`define PROP_DELAY 1.1
`define INVALID_DELAY 1.3

`define PERIOD 1.1
`define WIDTH 1.6
`define SETUP_TIME 2.0
`define HOLD_TIME 0.5
`define RECOVERY_TIME 3.0
`define REMOVAL_TIME 0.5
`define WIDTH_THD 0.0

`celldefine
module MY_FF (QN, VDD, VSS, A, B, CK);

inout VDD, VSS;
output QN;
input A, B, CK;
reg NOTIFIER;
supply1 xSN,xRN;
buf IC (clk, CK);
and IA (n1, A, B);
udp_dff_PWR I0 (n0, n1, clk, xRN, xSN, VDD, VSS, NOTIFIER);
not I2 (QN, n0);

wire ENABLE_B ;
wire ENABLE_A ;
assign ENABLE_B = (B) ? 1'b1:1'b0;
assign ENABLE_A = (A) ? 1'b1:1'b0;

specify
$setuphold(posedge CK &&& (ENABLE_B == 1'b1), posedge A,  `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_B == 1'b1), negedge A, `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_A == 1'b1), posedge B, `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_A == 1'b1), negedge B, `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$width(posedge CK,1.0,0.0,NOTIFIER);
$width(negedge CK,1.0,0.0,NOTIFIER);
if (A==1'b0 && B==1'b0)
(posedge CK => (QN:1'bx)) = (1.0, 1.0);
if (A==1'b1 && B==1'b0)
(posedge CK => (QN:1'bx)) = (1.0, 1.0);
if (B==1'b1)
(posedge CK => (QN:1'bx)) = (1.0,1.0);

endspecify

endmodule // MY_FF
`endcelldefine

`timescale 1ns/1ps
`celldefine
module MY_FF2 (QN, VDD, VSS, A, B, CK);

inout VDD, VSS;
output QN;
input A, B, CK;
reg NOTIFIER;
supply1 xSN,xRN;
buf IC (clk, CK);
and IA (n1, A, B);
udp_dff_PWR I0 (n0, n1, clk, xRN, xSN, VDD, VSS, NOTIFIER);
not I2 (QN, n0);

wire ENABLE_B ;
wire ENABLE_A ;
assign ENABLE_B = (B) ? 1'b1:1'b0;
assign ENABLE_A = (A) ? 1'b1:1'b0;

specify
$setuphold(posedge CK &&& (ENABLE_B == 1'b1), posedge A,  `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_B == 1'b1), negedge A,  `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_A == 1'b1), posedge B,  `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$setuphold(posedge CK &&& (ENABLE_A == 1'b1), negedge B,  `SETUP_TIME, `HOLD_TIME, NOTIFIER);
$width(posedge CK,1.0,0.0,NOTIFIER);
$width(negedge CK,1.0,0.0,NOTIFIER);
if (A==1'b0 && B==1'b0)
(posedge CK => (QN:1'bx)) = (1.0, 1.0);
if (A==1'b1 && B==1'b0)
(posedge CK => (QN:1'bx)) = (1.0, 1.0);
if (B==1'b1)
(posedge CK => (QN:1'bx)) = (1.0,1.0);

endspecify

endmodule // MY_FF2
`endcelldefine

--------------------------------------------------------

I am using the following Cadence versions:

MMSIM Version: 13.1.1.660.isr18

Virtuoso Version: IC6.1.8-64b.500.1

irun Version: 14.10-s039

Spectre Version: 18.1.0.421.isr9