• Skip to main content
  • Skip to search
  • Skip to footer
Cadence Home
  • This search text may be transcribed, used, stored, or accessed by our third-party service providers per our Cookie Policy and Privacy Policy.

  1. Community Forums
  2. Custom IC Design
  3. Clear/close a 'running' ADE-XL

Stats

  • Locked Locked
  • Replies 7
  • Subscribers 125
  • Views 4811
  • Members are here 0
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Clear/close a 'running' ADE-XL

TempViator
TempViator over 3 years ago

A situation I run into often is the need to close and clear an ADE-XL session, primarily to get a fresh starting point without closing my Cadence session.

The immediate problem I have is that I want to re-open the same ADE-XL as I was using, but I cannot because (per an error message) already running in another window.  There is no window where it exists, however.

What I'd like to do is clear it out in the same way I can close all open schematics, layouts, etc. by using CIW->File->Close Data.  But apparently this action has no effect on the ADE-XL. (Perhaps it is really a process, not a file?)

I feel like this must have a simple solution that I have just missed...?

(Cadence version is apparently 6.18.070.)

  • Cancel
Parents
  • ShawnLogan
    ShawnLogan over 3 years ago

    Dear TempViator,

    TempViator said:
    The immediate problem I have is that I want to re-open the same ADE-XL as I was using, but I cannot because (per an error message) already running in another window.  There is no window where it exists, however.

    As you may know, ADE-XL is no longer supported by Cadence. Hence, I might suggest you seriously consider migrating to Assembler or Explorer. The conversion process is quite easy and Assembler shares many of the commands of the former ADE-XL with a far more extensive set of features.

    In any case, I used ADE-XL for years and never experienced the error you suggest. Are you sure the view is just locked? What exactly is the error message? Our Cadence platforms no longer support ADE-XL and hence I cannot recreate your situation. However, as shown in Figure 1, Assembler does have a "Close" menu item.

    Shawn

    Figure 1

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
Reply
  • ShawnLogan
    ShawnLogan over 3 years ago

    Dear TempViator,

    TempViator said:
    The immediate problem I have is that I want to re-open the same ADE-XL as I was using, but I cannot because (per an error message) already running in another window.  There is no window where it exists, however.

    As you may know, ADE-XL is no longer supported by Cadence. Hence, I might suggest you seriously consider migrating to Assembler or Explorer. The conversion process is quite easy and Assembler shares many of the commands of the former ADE-XL with a far more extensive set of features.

    In any case, I used ADE-XL for years and never experienced the error you suggest. Are you sure the view is just locked? What exactly is the error message? Our Cadence platforms no longer support ADE-XL and hence I cannot recreate your situation. However, as shown in Figure 1, Assembler does have a "Close" menu item.

    Shawn

    Figure 1

    • Cancel
    • Vote Up 0 Vote Down
    • Cancel
Children
No Data

Community Guidelines

The Cadence Design Communities support Cadence users and technologists interacting to exchange ideas, news, technical information, and best practices to solve problems and get the most from Cadence technology. The community is open to everyone, and to provide the most value, we require participants to follow our Community Guidelines that facilitate a quality exchange of ideas and information. By accessing, contributing, using or downloading any materials from the site, you agree to be bound by the full Community Guidelines.

© 2025 Cadence Design Systems, Inc. All Rights Reserved.

  • Terms of Use
  • Privacy
  • Cookie Policy
  • US Trademarks
  • Do Not Sell or Share My Personal Information