sampled pnoise on multi-phase switched cap circuit

Hi jfyan,

A quick note.   Here's an article on sampleratio (you must have access to Cadence Online Support):

How to use the field "Sample Ratio" in pnoise type "sampled(jitter)" 

These are general Switched Capacitor filter articles

Measuring Noise in a Switched Capacitor Filter 

How to reconcile the linear noise, pnoise, and transient noise results on a switched capacitor ckt? 

best regards,

Tawna

thanks, Tawna,

I set sampleratio = 2 in noisetype = timedomain, is there any difference?  

regards

jeff

Hi Jeff,

What version of software are you using?    In virtuoso IC617ISR17, IC618, or ICADVM20.1 with Spectre 17.1ISR2 or later, 18.1, 19.1, 20.1 21.1, there are two noise types:   timeaverage and sampled(jitter).

noisetype=timedomain is pretty old (more than 5 years old).  See the article below:

How to use Pnoise Sampled analysis in Spectre (versions 18.1, 19.1, 20.1, 21.1) 

best regards,

Tawna

Hi Tawna,

we are using Version 19.1.0.237.isr3.

and here is my spectre script:

samplednoise pnoise start =100 stop=200k dec=50 pnoisemethod=fullspectrum
+noisetype=sampled measurement = [pm0] annotate = status sampleratio=1
pm0 jitterevent trigger = [clock_probe]
+triggerthresh = 0.5 triggernum=1 triggerdir = rise
+target = [vout 0]

it looks as i expected: the noise density lows by rt.2 if samplerration = 2 compared with 1 for white noise;

my following question is, I tried double the sampling freq. by using 2x clock on clock_probe while still keep sampleratio =1, I thought the result would be close to the case when sampleratio=2 and clock_probe=1x fund freq, but it is not. can you tell me why?  and which is the right one?

regards

jeff

Dear jfryan,

jfyan said:

my following question is, I tried doubling the pss. fund freq by using 2x clock on clock_probe while still keep sampleratio =1, I thought the result would be close to the case when sampleratio=2 and clock_probe=1x fund freq, but it is not. can you tell me why?  and which is the right one?

I did not see any details of your switched capacitor resistor noise test bench in your post, hence I do not know if you have included a lowpass filter on the resistor  noise. If you do not, or if the bandwidth of the lowpass filter is not sufficiently less than your value of fs/2, the resistor noise will be aliased. If so, the noise density you measure of the sampled noise will not be linear with sample frequency.

The impact of the sample frequency on the sampled output noise is discussed in the recent Forum post at URL:

https://community.cadence.com/cadence_technology_forums/f/custom-ic-design/49080/could-anyone-explain-this-sampled-noise-simulation-result

I performed a number of simulations in response to the post and included a note at URL:

noise_figure_nose_figure_sampled_sml_081521.pdf

that details the simulation results, the test bench, and a graphical illustration of the impact of sampling frequency on the resistor noise. If I understand your question, this may be of some relevance as I do not know your circuit under study.

Anyway, this came to mind and wanted to pass it your way in case it provides any insight into your question.

Shawn

thanks Shawn,

It is very helpful to read through the thread you posted.the following is the simple circuit I try to sim. the noise using pnoise.

if RC << Ton, KT/C noise will be on the output, and noise density is sqrt (KT/C*2/fund), if you run pss, and pnoise. fund = fs 

 but, if you look at the circuit, the noise should be updated at 2fs = 2fund, so the noise density should be the same as the case where the sampling clock is 2fs.

so, I think it is proper to use sampleratio= 2. which is quite similar to the example of clock multiplier that Tiwna posted. 

my following question is, can I use clockprobe feature in noisetype = sampled, where the probe clock is 2fs freq?

I thought the above two cases should be close to each other on the noise result.  but, it looks not, 2x clock probe doesn't reduce the noise density by sqrt2.. do you know why? 

thanks a lot for your help.

regards

jeff

First, I want to thank Shawn for stepping in and answering questions on the forum.   I appreciate you!  

Jeff, for in-depth technical questions, I suggest filing a Case on https://support.cadence.com .   There's actually an entire team of AEs who assist Cadence customers on technical questions like this  :-) 

(The Cadence AEs answering questions on this forum typically do so in their spare time: evenings, lunch hour, breaks, etc.)  

best regards,

Tawna

First, I want to thank Shawn for stepping in and answering questions on the forum.   I appreciate you!  

Jeff, for in-depth technical questions, I suggest filing a Case on https://support.cadence.com .   There's actually an entire team of AEs who assist Cadence customers on technical questions like this  :-) 

(The Cadence AEs answering questions on this forum typically do so in their spare time: evenings, lunch hour, breaks, etc.)  

best regards,

Tawna